Finncoatings® Color on the highest level

Important! Please do not add any air when stirring the paint as this is included in the paint film depending on the drying conditions. This would lead to an impairment of the surface and the load-bearing capacity of the coating.

TEMAFLOOR 25 CLEAR

 

CE logo 0809 Finncoatings®color on the highest level

 

DESCRIPTION        Finncoatings®color on the highest level
A one component moisture curing polyurethane primer and topcoat.


PRODUCT FEATURES
 Finncoatings®color on the highest level  
Easy to apply due to one component formulation.
Finncoatings®color on the highest level

RECOMMENDED USES
  Finncoatings®color on the highest level 
For varnishing of concrete, asbestos cement and other mineral floors. For topcoating of Mosaic floors.


TECHNICAL DATA
   Finncoatings®color on the highest level

Features    
Temafloor 25 Clear is dust binding and prevents impurities from being absorbed into the surface. Excellent resistance to abrasion.


Fire Classification: BFL-s1 according to EN 13501-1

Gloss groups    
Full-gloss

 

Coverage        Finncoatings®color on the highest level
Coverage on concrete floors is on the average 4 - 7 m2/l.
Practical coverage depends on the porosity of the substrate and on the application method.

 

Thinner    
1061

 

Application method    Finncoatings®color on the highest level

By brush or roller.

Drying time at 23°C and 50% relative air humidity     Dust dry after 1½ hours
Touch dry after 2 hours
Recoatable after 4-12 hours
Fully cured after 24 hours

Note! If the relative humidity of air is below 50% drying will be retarded.
Solids volume    

approx. 50 %.

Density     1,0 kg/l

APPLICATION DETAILS Finnc   Finncoatings®color on the highest leveloatings®color on the highest level

Application conditions    
The relative humidity of the concrete should not exceed 97%. The temperature of the ambient air, surface or coating should not fall below +5ºC during either application or drying. Relative humidity of air should be 50-90 %.


Preparation
   

New concrete
Remove laitance by power grinding or hydrochloric acid etching. Choose the method best suited for the premises. After grinding remove dust carefully with a vacuum cleaner. Hydrochloric acid etching is carried out with diluted hydrochloric acid (1 part concentrated hydrochloric acid, 4 parts water). Rinse with plenty of water and let the floor dry.

Old concrete   Finncoatings®color on the highest level
Remove all grease, oil, chemicals and other impurities by MAALIPESU detergent. Remove old peeling paint layer by grinding. Clean out pot-holes removing all loose friable material. Open cracks with e.g. an abrasive tool. Remove loose material and dust.

Cementitious levelling screed
Check compatibility with the levelling screed manufacturer.

Priming
   
Prime using 10% thinned Temafloor 25 Clear. Pour the varnish onto the floor and apply evenly. If the primer is absorbed into the concrete, repeat the priming immediately using "wet-on-wet" technique.


Patching
    Finncoatings®color on the highest level
Patch pot-holes and cracks with a mixture of Temafloor 200 Primer epoxy varnish and dry, clean sand of grain size 0.1-0.6 mm. Prepare the filler by adding a sufficient amount of sand into the varnish. Grind the patched areas before overcoating.


Cleaning of tools
       Finncoatings®color on the highest level
Thinner 006 1061.

 

EU VOC 2004/42/EC-limit value     VOC 2004/42/EC (cat A/i) 500 g/l (2010)Temafloor 25 Clear: max. VOC < 500 g/l

Finncoatings® Color on the highest level

 

Finncoatings  
Heidelberger Straße 8
74858 Aglasterhausen-Germany

 

Tel. + 49 (0)6262 917095
Fax  + 49 (0)6262 917791

www.finncoatings.com
Mail. This email address is being protected from spambots. You need JavaScript enabled to view it.