Finncoatings® Color on the highest level

 

Important! Please do not add any air when stirring the paint as this is included in the paint film depending on the drying conditions. This would lead to an impairment of the surface and the load-bearing capacity of the coating.

TEMAFLOOR 400

 

CE logo
DESCRIPTION
       Finncoatings®color on the highest level
A two component solvent free epoxy varnish.


PRODUCT FEATURES
 Finncoatings®color on the highest level  
Used as a binder for Temafloor 4000 grinding screed and epoxy concrete. Used also as a topcoat on top of Temafloor coatings and screeds.


RECOMMENDED USES
   
Suitable for dust binding and priming of new and old concrete floors under Temafloor coatings. Filled with sand also suitable for patching of concrete floors.


TECHNICAL DATA


Features        Finncoatings®color on the highest level
Fire classification according to standard EN 13501 is BFL-s1.


Gloss groups
   
Full-gloss
Finncoatings®color on the highest level

Coverage     

Coverage on concrete floors is on the average:
Primer                                 5 - 8 m2/l
Topcoat                             6 - 10 m2/l
Practical coverage depends on the porosity and evenness of the substrate and on the application method.

Thinner    
1029


Mixing ratio    

Base 3 parts by volume 008 4403

Hardener 1 part by volume 008 4408   Finncoatings®color on the highest level

Application method    

Pour the varnish mixture onto the floor, spread with a rubber trowel and level with a roller.

Pot-life (+23°C)     Approx. 30 minutes after mixing, on substrate.
Drying time at 23°C and 50% relative air humidity     

Dust dry after 6 hours
Recoatable after 16 - 24 hours
Fully cured 7 days

Solids volume        Finncoatings®color on the highest level
approx. 100 volume %

Density     1.1 kg / litre (mixture)

APPLICATION DETAILS

Application conditions    
The relative humidity of the concrete should not exceed 97%. The temperature of the ambient air, surface or coating should not fall below +15ºC during application or drying. Relative humidity of air should not exceed 80%.

Note! There is a natural tendency of epoxy coatings to chalk and discolor on exterior exposure.

Preparation
   

New concrete
Finncoatin   Finncoatings®color on the highest levelgs®color on the highest level
Remove laitance by power grinding, vacuum grit blasting or hydrochloric acid etching. Choose the method best suited for the premises. After grinding remove dust carefully with a vacuum cleaner. Hydrochloric acid etching is carried out with diluted hydrochloric acid (1 part concentrated hydrochloric acid, 4 parts water). Rinse with plenty of water. Dry the floor.

Old concrete   Finncoatings®color on the highest level
Remove all grease, oil, chemicals and other impurities by MAALIPESU detergent. Remove old peeling paint layer by grinding or vacuum grit blasting. Choose the method best suited for the premises. Clean out pot-holes removing all loose friable material. Open cracks with e.g. an abrasive tool. Remove loose material and dust.
Cementitious levelling screed
Check compatibility with the levelling screed manufacturer.

Priming
   
Prime using about 30% thinned Temafloor 400 epoxy varnish. Pour the varnish onto the floor and apply as much as is needed to impregnate the concrete surface. If necessary, repeat the priming to get a non-porous surface. Subsequent treatment can be carried out after

2 hours using "wet-on-wet" technique.

Patching
   
Patch pot-holes and cracks with a mixture of unthinned Temafloor 400 epoxy varnish and dry, clean sand. Mixing ratio e.g. 1 part by volume of epoxy mixture and 1-2 parts by volume of sand of grain size 0.5-1.2 mm.


Overcoating
       Finncoatings®color on the highest level
Overcoating should be done within 16-24 hrs after priming. If the primed surface is not overcoated within 24 hrs, it should be abraded. Use unthinned Temafloor 400 varnish for the topcoat. Pour the varnish mixture onto the floor, spread with a rubber trowel and level with a roller.


Mixing of components
    Finncoatings®color on the highest level
Mix the correct proportions of base and hardener thoroughly (approx. 2 minutes) by using a low speed hand drill with a paddle. The amount of mixture depends on the area to be coated and on the pot life of the mixture. Insufficient mixing or incorrect mixing ratio will result in uneven drying of the surface, weaken the properties of the coating and risk the success of the application.


Cleaning of tools
       Finncoatings®color on the highest level
Thinner 006 1029.

EU VOC 2004/42/EC-limit value     VOC 2004/42/EC (cat A/j) 500 g/l (2010)Temafloor 400: max. VOC < 500 g/l

 

The European harmonized productstandard EN 13813 defines the requirements for Screed materials and floor screeds, including synthetic resin screeds.
This product is tested and CE-labelled in accordance with the tables ZA.1.5 and ZA.3.3 in the appendix ZA.3.

 

 

 

 

CE logo
 

 

 

 

Tikkurila Oyj
Kuninkaalantie 1
FI-01300 VANTAA
11Finncoatings®color on the highest level
TIK-8400-5005b
EN 13813 SR-B2,0-IR 4
Primer/Screed/Sealer
Abrasion resistance
NPD
Chemical resistance
CR 1, 2, 5, 6b, 7…8, 10…12, 14 (Class 2)
   
Release of corrosive substances
SR
Impact resistance
IR4Finncoatings®color on the highest level
Sound insulation
NPD
Sound absorption
NPD
Thermal resistance
NPD
Reaction to fire
Bfl
Water permeability
0.015
Adhesion
B 2.0

 

The European harmonized productstandard EN 1504-2 defines the requirements for surface protection systems for concrete.
This product is tested and CE-labelled in accordance with the tables 1d, 1f and 1g in the
appendix ZA.

 

 

 

CE logo
0809

 

 

 

Tikkurila Oyj
Kuninkaalantie 1
FI-01300 VANTAA  Finncoatings®color on the highest level
13
TIK-8400-5005a Finncoatings®color on the highest level
0809-CPD-0773
EN 1504-2:2004
Product for protection and repair of concrete structures – Coating
Abrasion resistance
< 3000 mg
Resistance to severe chemical attack
Class II
   
Permeability to CO2
CO2sD > 50 m
Water absorption
w < 0,1 kg/m²∙h0,5
Impact resistance
Class I: ≥ 4 Nm
Permeability to water vapour
Class II, 5 m < sD < 50 m

 

FiFinncoatings® Color on the highest levelngs®

Finncoatings  
Heidelberger Straße 8
74858 Aglasterhausen-Germany

 

Tel. + 49 (0)6262 917095
Fax  + 49 (0)6262 917791

www.finncoatings.com
Mail. This email address is being protected from spambots. You need JavaScript enabled to view it.

color on the highest level